Nie masz w koszyku żadnych produktów
 
English Polski Spanish 
Szukaj instrukcji do
 

(e.g. AA-V20EG JVC, ZX-7 Sony )
PayPal 1000+ rating Secure, Encrypted Checkout.
 
Kto jest w sklepie?
Sklep przegląda 5979 gości 
Kategorie
Informacje
Polecamy
Strona główna >> JVC >> RX-E112RSL Instrukcja Obsługi
 
 0 szt. w koszyku 

JVC RX-E112RSL
Instrukcja Obsługi


Tweetnij o tym produkcie a dostaniesz $1.00 rabatu!
  • Plik do pobrania
  • Format PDF
  • Kompletna instrukcja
  • Język: English
Cena: $4.99

Opis JVC RX-E112RSL Instrukcja Obsługi

Kompletna instrukcja obsługi w formie pliku PDF. Plik PDF zostanie dostarczony na Twój adres email po jego zakupieniu.

Instrukcje obsługi (czasami nazywane także podręcznikiem użytkownika) opisuja funkcje i sposób działania danego produktu.

Instrukcja jest dostępna w następujących językach: English

Plik nie jest jeszcze gotowy
Musisz najpierw dokonać zakupu.

Recenzje produktu
Dla tego produktu nie napisano jeszcze recenzji!

Tekstowy podgląd strony 9 (kliknij aby zobaczyć)
AM (MW/LW) antenna connection
Connect the AM (MW/LW) loop antenna supplied to the AM LOOP terminals. Turn the loop until you have the best reception. � If the reception is poor, connect an outdoor single vinyl-covered wire to the AM EXT terminal. Keep the AM (MW/LW) loop antenna connected.

Connecting the Speakers
After connecting the front, center and rear speakers, and/or a subwoofer, set the speaker setting information properly to obtain the best possible Surround effect. For details, see page 15. CAUTION:
Use speakers with the SPEAKER IMPEDANCE indicated by the speaker terminals.

FM antenna connection
Connect the FM antenna supplied to the FM 75 � COAXIAL terminal as temporary measure. Extend the supplied FM antenna horizontally. � If the reception is poor, connect an outdoor FM antenna (not supplied). Before attaching a 75 � coaxial cable (with a standard type connector), disconnect the supplied FM antenna.

Connecting the front, center, and rear speakers

1

2
2 1

3

Notes: � If the AM (MW/LW) loop antenna wire is covered with vinyl, remove the vinyl while twisting it as shown on the right. � Make sure the antenna conductors do not touch any other terminals, connecting cords and power cord. This could cause poor reception.

For each speaker, connect the (+) and (�) terminals on the rear panel to the (+) and (�) terminals marked on the speakers respectively.

1 Cut, twist and remove the insulation at the end of each speaker cord (not supplied). 2 Press and hold the clamp of the speaker terminal (1), then insert the speaker cord (2). 3 Release the finger from the clamp.
Connecting the subwoofer speaker
By connecting a subwoofer, you can enhance the bass or reproduce the original LFE signals recorded in the digital software.

RIGHT RIGHT

LEFT/MONO

Getting Started

INPUT (LOW-LEVEL)

Powered subwoofer (example)

SUBWOOFER OUT

Connect the input jack of a powered subwoofer to the SUBWOOFER OUT jack on the rear panel, using a cable with RCA pin plugs (not supplied). � Refer also to the manual supplied with your subwoofer.

Note: You can place a subwoofer wherever you like since bass sound is non-directional. Normally place it in front of you.

5

Klienci kupując ten produkt kupili także

$4.99

RXE112RSL JVC
Instrukcja Serwisowa

Kompletna instrukcja serwisowa w formie pliku PDF. Instrukcje serwisowe zazwyczaj zawierają schemat…
>
Parse Time: 1.148 - Number of Queries: 100 - Query Time: 0.548