|
|
|
Kto jest w sklepie?
Sklep przegląda 5806 gości |
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
Dobrej jakości skan - wkońcu mogłem poznać wszystkie funkcje tego odtwarzacza - polecam .
;
Gruba instrukcja - poprostu wszystko co potrzreba - polecam .
Speaker and signal indicators on the display
By checking the following indicators, you can easily confirm which speakers you are activating and which signals are coming into this receiver. Speaker indicators Signal indicators
Selecting different sources for picture and sound
While watching pictures from a video source, you can listen to sound of an audio source. � Once you have selected a video source, pictures of the selected source are sent to the TV until you select another video source. Press one of the audio source selection buttons while viewing the picture from a video component such as the VCR or DVD player, etc.
CD FM/AM
L
LS
C
R
RS
L
LS
C
S SB
R
LFE RS
SUBWFR
SB
CD
TAPE/CDR
FM
AM
TAPE/CDR
On the unit What speaker indicators light depends on the speaker setting (for details, see �Setting the Speakers� on page 25). � The frames of �L,� �C,� �R,� �LS,� �RS, � and �SB� light up, when the corresponding speakers are set to �LARGE� or �SMALL� and when the speaker is required for the Surround/DSP mode currently selected. � When �SUB WOOFER� is set to �YES,� SUBWFR lights up (see page 25). � All three frames on the row of �SB� are not used at the same time. When �SBACK OUT� is set to �2SPK,� the left and the right ones are used. When it is set to �1SPK,� the middle one is used (see page 26). The signal indicators light up to show the incoming signals. L: � When digital input is selected: Lights up when the left channel signal comes in. � When analog input is selected: Always lights up. R: � When digital input is selected: Lights up when the right channel signal comes in. � When analog input is selected: Always lights up. C: Lights up when the center channel signal comes in. LFE: Lights up when the LFE channel signal comes in. LS: Lights up when the left surround channel signal comes in. RS: Lights up when the right surround channel signal comes in. S: SB: Lights up when the monaural surround channel signal comes in. Lights up when the surround back channel signal comes in.
On the remote
Note:
When you watch the picture through the COMPONENT VIDEO jacks, you cannot use this function.
Adjusting the Volume
RX-7032V
AUDIO/VIDEO CONTROL RECEIVER
On the front panel: To increase the volume, turn MASTER VOLUME clockwise. To decrease the volume, turn it counterclockwise. From the remote control:
To increase the volume, press VOLUME +. To decrease the volume, press VOLUME �. CAUTION:
Note:
When �DVD MULTI� is selected as the source, �L,� �C,� �R,� �LFE,� �LS,� and �RS� light up.
Always set the volume to the minimum before starting any sources. If
Notes: How to understand the speaker and signal indicator illumination
� The volume level can be adjusted within the range of �0� (minimum) to �70� (maximum). � If you set One Touch Operation to �ON� (see page 28), you do not have to adjust the volume level each time you change the source. It is automatically set to the stored level.
L
LS
C
R
RS
SUBWFR LFE
SB
Ex. No sound comes out of the center speaker and surround back speakers though center channel and surround back channel signals are coming into this receiver.
16
English
the volume is set at its high level, the sudden blast of sound energy can permanently damage your hearing and/or ruin your speakers.
|
|
|
> |
|
