JVC RX-7020VBK
Instrukcja Obsługi

Changing the source name
When you have connected a CD recorder to the TAPE/CDR jacks or the DBS tuner to the TV SOUND/DBS jacks on the rear panel, change the source name which will be shown on the display.
Remote NOT

Adjusting the Volume
On the front panel:
To increase the volume, turn MASTER VOLUME clockwise. To decrease the volume, turn it counterclockwise.
MASTER VOLUME

When changing the source name from �TAPE� to �CDR�:

1 2

Press TAPE/CDR (SOURCE NAME) to select �TAPE� as the source. Press and hold SOURCE NAME (TAPE/CDR) to assign �CDR.�

TAPE/CDR
SOURCE NAME

From the remote control:
To increase the volume, press VOLUME +. To decrease the volume, press VOLUME �.

+
VOLUME

�

TAPE/CDR
SOURCE NAME

CAUTION:
Always set the volume to the minimum before starting any source. If the volume is set at its high level, the sudden blast of sound energy can permanently damage your hearing and/or ruin your speakers.

When changing the source name from �TV SOUND� to �DBS�:

1

Press TV SOUND/DBS (SOURCE NAME) to select �TV SOUND� as the source. Press and hold SOURCE NAME (TV SOUND/DBS) to assign �DBS.�

TV SOUND/DBS
SOURCE NAME

Note: The volume level can be adjusted within the range of �0� (minimum) to �50� (maximum).

2

TV SOUND/DBS
SOURCE NAME

Selecting the Front Speakers
To change the source name to �TAPE� or �TV SOUND,� repeat the same procedure above.
Notes: � To watch the picture from DBS tuner, change the source name to �DBS.� If �TV SOUND� is selected, you cannot watch the picture from DBS tuner. � Without changing the source name, you can still use the connected components. However, there may be some inconvenience. � �TAPE� or �TV SOUND� will appear on the display when you select the CD recorder or DBS tuner. � You cannot use the digital input (see page 15) for the CD recorder. � You cannot use the COMPU LINK remote control system (see page 31) to operate the CD recorder.

Remote NOT

When you have connected two pairs of the front speakers, you can select which to use.
1 SPEAKERS ON/OFF 2

Selecting different sources for picture and sound
You can watch picture from a video component while listening to sound from another component. Press one of the audio source selecting buttons � CD, TAPE/CDR, PHONO, FM/AM, while watching the picture from a video component such as the VCR, DVD player, or DBS tuner, etc.
DVD MULTI DVD VCR TV SOUND/DBS

To use the speakers connected to the FRONT SPEAKERS 1 terminals, press SPEAKERS ON/OFF 1 so that the SPK 1 indicator lights up on the display. (Make sure that the SPK 2 is not lit on the display.) To use the speakers connected to the FRONT SPEAKERS 2 terminals, press SPEAKERS ON/OFF 2 so that the SPK 2 indicator lights up on the display. (Make sure that the SPK 1 is not lit on the display.) To use both sets of the speakers, press SPEAKERS ON/OFF 1 and 2 so that the SPK 1 and SPK 2 indicators light up on the display. To use neither sets of the speakers, press SPEAKERS ON/OFF 1 and 2 so that the SPK 1 and SPK 2 indicators disappear from the display.
Notes: � If you select any of the Surround modes while using both the speakers connected to the FRONT SPEAKERS 1 and 2 terminals, the speakers connected to the FRONT SPEAKERS 2 terminals are deactivated. � While the surround mode is in use, you can only select either the speakers connected to the FRONT SPEAKERS 1 or 2 terminals. � If you select the source to DVD MULTI while using both the speakers connected to the FRONT SPEAKERS 1 and 2 terminals, the speakers connected to the FRONT SPEAKERS 2 terminals are deactivated. � When selecting �DVD MULTI� as the source, you can only select either the speakers connected to the FRONT SPEAKERS 1 or 2 terminals.

Basic Operations

DVD
SOURCE NAME

DVD MULTI VCR

CD TAPE/CDR

FM/AM PHONO

CD

TAPE/CDR
SOURCE NAME

PHONO

FM/AM

TV/DBS

On the front panel
Notes:

From the remote control

� Once you have selected a video source, pictures of the selected source are sent to the TV until you select another video source. � This function can use only when selecting the S-video or composite video input terminal.

11