Nie masz w koszyku żadnych produktów
 
English Polski Spanish 
Szukaj instrukcji do
 

(e.g. AA-V20EG JVC, ZX-7 Sony )
PayPal 1000+ rating Secure, Encrypted Checkout.
 
Kto jest w sklepie?
Sklep przegląda 5833 gości 
Kategorie
Informacje
Polecamy
Strona główna >> JVC >> HR-S5800AM Instrukcja Obsługi
 
 0 szt. w koszyku 

JVC HR-S5800AM
Instrukcja Obsługi


Tweetnij o tym produkcie a dostaniesz $1.00 rabatu!
  • Plik do pobrania
  • Format PDF
  • Kompletna instrukcja
  • Język: English
Cena: $4.99

Opis JVC HR-S5800AM Instrukcja Obsługi

Kompletna instrukcja obsługi w formie pliku PDF. Plik PDF zostanie dostarczony na Twój adres email po jego zakupieniu.

Instrukcje obsługi (czasami nazywane także podręcznikiem użytkownika) opisuja funkcje i sposób działania danego produktu.

Instrukcja jest dostępna w następujących językach: English

Plik nie jest jeszcze gotowy
Musisz najpierw dokonać zakupu.

Recenzje produktu
Dla tego produktu nie napisano jeszcze recenzji!

Tekstowy podgląd strony 59 (kliknij aby zobaczyć)
EN
RECORDING
SYMPTOM
1. Recording cannot be started.

59

POSSIBLE CAUSE
� There is no cassette loaded, or the cassette loaded has had its Record Safety tab removed. � "L-1", "F-1", "S-1" or "S-2" has been selected as the input mode. � The source (another video recorder, camcorder) has not been properly connected. � All necessary power switches have not been turned on. � The input mode is not correct. � The camcorder has not been properly connected. � The input mode is not correct.

CORRECTIVE ACTION
Insert a cassette, or using adhesive tape, reseal the slot where the tab was removed. Set to the desired channel. Confirm that the source is properly connected. Confirm that all units' power switches are turned on. Set the input mode to "L-1", "F-1", "S1" or "S-2". Confirm that the camcorder is properly connected. Set the input mode to "L-1", "F-1", "S1" or "S-2".

2. TV broadcasts cannot be recorded. 3. Tape-to-tape editing is not possible.

4. Camcorder recording is not possible.

TIMER RECORDING
SYMPTOM
1. Timer recording won't work.

POSSIBLE CAUSE
� The clock and/or the timer have been set incorrectly. � The timer is not engaged. � Timer recording is in progress.

CORRECTIVE ACTION
Re-perform the clock and/or timer settings. Press � and confirm that "�" is displayed on the display panel. Timer programming can't be performed while a timer recording is in progress. Wait until it finishes. Load a cassette with the Record Safety tab intact, or cover the hole using adhesive tape. Remove the cassette and cover the hole with adhesive tape, or insert a cassette with the Record Safety tab intact. Check the programmed data and reprogram as necessary, then press � again. The programme may not have been recorded in its entirety. Next time make sure you have enough time on the tape to record the entire programme. Refer to "G-CODE/SHOWVIEW System Setup" and re-perform the procedure. ( pg. 26)

2. On-screen timer programming is not possible. 3. "�" and "]" on the display panel won't stop blinking.

� The timer is engaged but there's no cassette loaded. � The loaded cassette has had its Record Safety tab removed.

4. "�" blinks for 10 seconds and the Timer mode is disengaged.

� � has been pressed when there are no programs in memory, or the timer record information has been programmed incorrectly. � The end of the tape was reached during timer recording.

5. The power shuts off and "�" and "]" won't stop blinking.

6. The G-CODE/SHOWVIEW system does not timer-record properly.

� The recorder's channel positions have been set incorrectly.

Klienci kupując ten produkt kupili także

$4.99

HRS5800AM JVC
Instrukcja Serwisowa

Kompletna instrukcja serwisowa w formie pliku PDF. Instrukcje serwisowe zazwyczaj zawierają schemat…
>
Parse Time: 0.166 - Number of Queries: 103 - Query Time: 0.038