Nie masz w koszyku żadnych produktów
 
English Polski Spanish 
Szukaj instrukcji do
 

(e.g. AA-V20EG JVC, ZX-7 Sony )
PayPal 1000+ rating Secure, Encrypted Checkout.
 
Kto jest w sklepie?
Sklep przegląda 5665 gości 
Kategorie
Informacje
Polecamy
Strona główna >> JVC >> GRDVX400EG/EK Instrukcja Serwisowa
 
 0 szt. w koszyku 

JVC GRDVX400EG/EK
Instrukcja Serwisowa


Tweetnij o tym produkcie a dostaniesz $1.00 rabatu!
  • Zawiera schematy
  • Plik do pobrania
  • Format PDF
  • Kompletna instrukcja
  • Język: English
Cena: $4.99

Opis JVC GRDVX400EG/EK Instrukcja Serwisowa

Kompletna instrukcja serwisowa w formie pliku PDF. Instrukcje serwisowe zazwyczaj zawierają schematy, diagramy drukowanych obwodów (PCB), schematy połączeń, schematy blokowe oraz katalog części. Instrukcje serwisowe są wykorzystywane glównie przez osoby naprawiające uszkodzony sprzęt.

Jeśli chcesz się dowiedzieć jak się obsługuje Twój telewizor, magnetowid, odtwarzacz mp3 itp. powinieneś raczej szukać instrukcji obsługi

Instrukcja jest dostępna w następujących językach:

Plik nie jest jeszcze gotowy
Musisz najpierw dokonać zakupu.

Recenzje produktu
Dla tego produktu nie napisano jeszcze recenzji!
Recenzje innych produktów
 ST-8077K TECHNICS Instrukcja Serwisowa by Adam Grążka;
...instruction is ok. ...instrukcja jest ok. Thanks/Dzięki
 T5 SANSUI Instrukcja Serwisowa by Adam Grążka;
Documentation made ​​available quickly and It is good quality. Thanks.

Tekstowy podgląd strony 36 (kliknij aby zobaczyć)
2.8.2 Tape pattern check (1) Play back the compatibility adjustment tape. (2) While triggering the MAIN CN105-11PIN (HID1), observe the waveform of CN105-29PIN (ENV_OUT). (3) Confirm that the waveform is free from remarkable level-down, and entirely parallel and straight. Moreover, perform the following adjustment as required. (4) In case any level-down is observed on the left hand side, straighten the level by turning the guide roller of the pole base assembly (supply). In case any level-down is observed on the right hand side, however, straighten the level by turning the guide roller of the pole base assembly (Take-up). (5) After adjustment, try the unloading motion once, and confirm that the waveform is flat (straight) when the tape has been played back again. Moreover, perform readjustment as required. (6) When the recording has been played back again, play back the self-recording to confirm that the waveform is flat. Note: When an adjustment is performed with the lower case cover attached, first slide the Cover (M.ADJ) open and then perform the compatibility adjustment. Be sure not to damage the cover plate when sliding it open to make an adjustment because it must be re-positioned after completing the adjustment.

CN105-29 (ENV_OUT)

CN105-11 (HID1)

Fig. 2-8-3

Flatten the waveform. Misalignment of guide roller height on the supply side Misalignment of guide roller height on the take-up side

Fig. 2-8-4

2-21

Klienci kupując ten produkt kupili także

$4.99

GR-DVX400EG/EK JVC
Instrukcja Obsługi

Kompletna instrukcja obsługi w formie pliku PDF. Plik PDF zostanie dostarczony na Twój adres email…
>
Parse Time: 0.146 - Number of Queries: 103 - Query Time: 0.034