|
|
|
Kto jest w sklepie?
Sklep przegląda 5842 gości |
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
Szybko, sprawnie i tanio. Serwis godny polecenia. Będę polecał innym
 ;
Ogólnie jest OK, z wyjątkiem obrazu płyty głównej, który jest miejscami mało czytelny, ale można sobie poradzić.
;
Dokładna dokumentacja, pomogła w szybkiej naprawie telewizora. Dziękuję!
;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
5.1.2 FINAL ASSEMBLY, REAR ASSEMBLY(G) AND SHOE ASSEMBLY(G) <M2>
<M2> FINAL ASS'Y REAR ASS'Y(G) SHOE ASS'Y(G) OP FRAME ASS'Y
TABLE OF SETTING TORQUE FOR SCREW DRIVER PART.NO
112 121 126 127 128 132 133
133 123
NOTES 132 1. BEND FPC , AND PASS THE CORNER HOLE OF THE SHEET METAL . 2. BE CAREFUL NOT TO CUT FPC BY THE SHEET METAL EDGE . p1 p2 3. NOTE IT EXTERNALS WHERE THE DENT IS NOT IN FPC WITH THE WOUND . 4. DO NOT TOUCH BY THE FINGER TERMINAL AREA OF FPC . 147 NOTES
291 SHOE ASS'Y
COVER(SHOE)
124
ASS'Y OP FRAME ASS'Y
104
SETTING TORQUE 0.07 ±0.007 N�m 0.10 ±0.010 N�m 0.08 ±0.008 N�m
u
BKT(H.S) 292
119 f
p1 n
OTHER SCREW
294 BKT (SHOE MIC)
SHOE ASS'Y(G) LYH20612
r
146 PROCESS THIS PART OF DRUM MOTOR FPC TO THE SHIELDING CASE . g q 126 g a2 125 120 a1 109 m g 131
FRONT ASS'Y(G)
(Refer to the Exploded view for this part.)
p2 293
FIG.1 DRUM MOTOR FPC PROCESSING CHART
LOWER CASE ASS'Y
<02> JACK BOARD ASS'Y
b 113
102 nf s3 s1 r
LOWER CASE ASS'Y
(Refer to the Exploded view for this part.)
152
SHIELD
h1 j2 h2 j1 j4
S TERMINAL
g j3 j6
c
k1
COVER(PR)
108 151 112 113 u 110
s4 z3 s2 z2 k3 p1
p2 135 k2 p1 p2 k2
SUPPRESS FROM BOTH SIDES OF UPPER AND LOWER FIRMLY, AND TIGHTEN FROM RIGHT SCREW.
1 mm
s3 'h1 'h2
FIG.2 STOPPER(JACK) INSTALLATION CHART
111 j1 116 a2 b r a1 q m j2 c
113 115
d
114
z2 121 z1 k3
s4 j3 'h1 j6 h1 h2 j5 j4 110 'h2 t
j5 s1
(Refer to the Exploded view for this part.)
<M3> MECHANISM ASS'Y
z3
103
BASE
y 145
122
REAR ASS'Y(G)
134
UPPER ASS'Y(G)
148
s2
105
BKT(MECHA) ASS'Y
d
<04> PRE/MDA BOARD ASS'Y
117
REAR ASS'Y(G) LYH20611
PASTE ACCORDING TO THE CORNER OF THIS COIL AND APPLY IT. 283 282
145 IT MATCHES IT TO THE END FACE OF C6202. C6202 DO NOT PUT EXTERNAL FORCE ON THE FPC ROOT WHEN BENDING IT.
REAR UNIT 281
SOLDERING
t
IT MATCHES IT TO THE END FACE OF THE PWB.
e 130 y z1 e
<01> MAIN BOARD ASS'Y
285 287 PUT IT SO THAT THE SHEET SHOULD NOT FLOAT. ESPECIALLY, NOTE THE PWB END FACE SIDE. FIG-2. SHIELD AFFIXATION POSITION 284 285 <03> REG BOARD ASS'Y DO NOTON THE FPC ROOT. FORCE PUT EXTERNAL
FIG-1. SPACER AFFIXATION POSITION 128 127 129
OP FRAME ASS'Y J2G TYPE
118
J7C TYPE BKT(OP-J7) ASS'Y 106
SPACER DOSE NOT GO UP PART OF BKT. STICKING AS SHOWN IN FIGURE. (MACHING TO FRONT EDGE.)
149
118 w
SPACER(A)
150
FINAL ASS'Y LYH20608
THE INTERIOR SIDE IS A CORNER HOLE MATCH OF OP BKT. 154
BKT (OP-J2) ASS'Y
THE INTERIOR SIDE IS ARM BKT MATCH. EDGE MATCH OF SCREW.
106
STICKING AS SHOWN IN FIGURE. (MACHING TO FRONT EDGE.)
143 (Refer to the Exploded view for this part.) 107 PEEL OFF, PASTE A TWO SIDED TAPE, AND APPLY IT. FIG.4 SPACER(MECHA) INSTALLATION CHART (M3D4L) MATCHING TO EDGE FASE OF MAIN PWB.
OP BLOCK ASS'Y
OP BLOCK ASS'Y 143
(Refer to the Exploded view for this part.)
t
w
138
SPACER(A)
BEND SOLDERING
SPACER(A)
SOLDERING
BKT(OP-J7)2
137 136 t
SPACER(A)
STICKING AS SHOWN IN FIGURE. (MACHING TO LEFT EDGE.)
153 FIG.3 SPACER(MECHA) INSTALLATION CHART (M3D6L)
<10> CCD BOARD ASS'Y
SPACER(A) 139
<10> CCD BOARD ASS'Y
<M2>
185
188
189
184
THE KNOB IS C.COVER SIDE AS SHOWN IN FIGURE.
186
CASSETTE HOUSING
187
190 9 mm A
RATING LABEL
192
IN WATCHING, THERE MUST BE NEITHER BENDING OF THE STICKER NOR GREAT MISREGISTRATION.
A SIDE LABEL AFFIXATION POSITION
DRAWING FOR STICKER(C) STICKING
CLEANER ASS'Y LYH20604
5-2
|
|
|
> |
|
