Nie masz w koszyku żadnych produktów
 
English Polski Spanish 
Szukaj instrukcji do
 

(e.g. AA-V20EG JVC, ZX-7 Sony )
PayPal 1000+ rating Secure, Encrypted Checkout.
 
Kto jest w sklepie?
Sklep przegląda 5644 gości 
Kategorie
Informacje
Polecamy
Strona główna >> JVC >> GM-X50C Instrukcja Obsługi
 
 0 szt. w koszyku 

JVC GM-X50C
Instrukcja Obsługi


Tweetnij o tym produkcie a dostaniesz $1.00 rabatu!
  • Plik do pobrania
  • Format PDF
  • Kompletna instrukcja
  • Język: English
Cena: $4.99

Opis JVC GM-X50C Instrukcja Obsługi

Kompletna instrukcja obsługi w formie pliku PDF. Plik PDF zostanie dostarczony na Twój adres email po jego zakupieniu.

Instrukcje obsługi (czasami nazywane także podręcznikiem użytkownika) opisuja funkcje i sposób działania danego produktu.

Instrukcja jest dostępna w następujących językach: English

Plik nie jest jeszcze gotowy
Musisz najpierw dokonać zakupu.

Recenzje produktu
Dla tego produktu nie napisano jeszcze recenzji!

Tekstowy podgląd strony 38 (kliknij aby zobaczyć)
Self-diagnostic Indication
When something abnormal occurs with the Monitor, this function informs you of the condition of the Monitor with self-diagnostic lamps, allowing for smooth service work.
Remote sensor 1 2 3 Power lamp Self-diagnostic lamps (1 to 3)
MENU INPUT

If the trouble still persists, follow the procedure below:

1

Check which lamps are lighting or flashing.
On the Self-diagnostic Report Sheet (below), check the box next to �Lights� or �Flashes� of the corresponding lamp or lamps. � Only one lamp may light or flash, or all three lamps may do so.

2 3 4

Switch off the POWER switch on the back of the Monitor. Unplug the power cord. Call your dealer and tell which lamps are lighting or flashing. (Copy and fax the Self-diagnostic Report Sheet below.)

� If the screen monitor turns off and self-diagnostic lamps light or flash
If the self-diagnostic lamps light or flash in red, check the following before consulting the dealer where you purchased the Monitor. � If self-diagnostic lamp 1 (upper) flashes, lamp 2 (middle) lights, and lamp 3 (lower) flashes This may be caused by the dusty intakes on the rear. If this happens, switch off the main power by POWER switch (set to �� (off)�), unplug the AC power cord, then clean the intakes by referring to the instruction on page 2. � After cleaning, switch on the Monitor�s main power again. If self-diagnostic lamps do not go off, consult your dealer immediately.

Note: If you switch on the main power immediately after switching it off (or after recovering from a brief power interruption), the self-diagnostic lamps may light (or flash), and no image may appear on the screen. In this case, switch off the main power again, wait for about 10 seconds, then switch it on again. If no self-diagnostic lamps light or flash, you can operate and use the Monitor as usual.

Self-diagnostic Report Sheet
Store name where you purchased the Monitor

� If the screen monitor dims a little and �TEMP. OVER� lights (or flashes)
If �TEMP. OVER� lights or flashes at the right bottom of the screen, check the following before consulting the dealer where you purchased the Monitor. �TEMP. OVER� appears to warn you of the internal heat buildup, which is usually caused by accumulated dust around the intakes or by improper installation. If the cause of the internal heat buildup is eliminated, this indication disappears and the screen recovers the brightness. � If �TEMP. OVER� flashes in yellow This may be caused by the dusty intakes on the rear. If this happens, switch off the main power by POWER switch (set to �� (off)�), unplug the AC power cord, then clean the intakes by referring to the instruction on page 2. � After cleaning, switch on the Monitor�s main power again. If �TEMP. OVER� still flashes, this trouble may be caused by improper installation or improper location of the Monitor. In this case, consult your dealer immediately to solve this improper installation and to improve the circumstances around the Monitor. � If �TEMP. OVER� lights in red �TEMP. OVER� will be shown for abut two minutes, the Monitor will shut off automatically, then the Selfdiagonal lamps light in red. If this happens, switch off the main power by POWER switch (set to �� (off)�), unplug the AC power cord, then consult your dealer immediately.

To
Model Name: Plasma Display Monitor GM-X50C
The self-diagnostic lamps light or flash as listed on the following table. Please give me immediate advice or service if necessary.
Self-diagnostic lamps

NO. Lamp position 1 2 3 Upper Middle Lower TEMP. OVER

Conditions

& Lights & Lights & Lights & Lights

& Flashes & Flashes & Flashes & Flashes

Your Name: Telephone No.: Address:

37

Klienci kupując ten produkt kupili także

$4.99

SX-K700 TECHNICS
Instrukcja Obsługi

Kompletna instrukcja obsługi w formie pliku PDF. Plik PDF zostanie dostarczony na Twój adres email…

$4.99

CJ-V51 PIONEER
Instrukcja Serwisowa

Kompletna instrukcja serwisowa w formie pliku PDF. Instrukcje serwisowe zazwyczaj zawierają schemat…

$4.99

GRAND PRIX ELECTRONIC 754 BECKER
Instrukcja Serwisowa

Kompletna instrukcja serwisowa w formie pliku PDF. Instrukcje serwisowe zazwyczaj zawierają schemat…

$4.99

SX-PR602 TECHNICS
Instrukcja Serwisowa

Kompletna instrukcja serwisowa w formie pliku PDF. Instrukcje serwisowe zazwyczaj zawierają schemat…

$4.99

EV-S1000E SONY
Instrukcja Obsługi

Kompletna instrukcja obsługi w formie pliku PDF. Plik PDF zostanie dostarczony na Twój adres email…

$4.99

GRAND PRIX ELECTRONIC 780 BECKER
Instrukcja Serwisowa

Kompletna instrukcja serwisowa w formie pliku PDF. Instrukcje serwisowe zazwyczaj zawierają schemat…

$4.99

AG7330 PANASONIC
Instrukcja Serwisowa

Kompletna instrukcja serwisowa w formie pliku PDF. Instrukcje serwisowe zazwyczaj zawierają schemat…

$4.99

EVO-9850 VOLUME 1 SONY
Instrukcja Serwisowa

Kompletna instrukcja serwisowa w formie pliku PDF. Instrukcje serwisowe zazwyczaj zawierają schemat…
>
Parse Time: 0.173 - Number of Queries: 130 - Query Time: 0.038